Dryer Vent Cleaning in Leander, TX | Resolute Chimney Sweep

Dryer Vent Cleaning in Leander — Flat-Price Sweep, Findings in Writing

A flat-price sweep with a camera inspection and photo report included. If we find something that needs attention, you see the picture before you hear a price — and we will tell you when it can wait.

Flat price quoted before we book

28+
Cities Served
Free
Written Quotes
Licensed & Insured Written Quotes Free Estimates All Brands Satisfaction Guarantee
Sweep & inspectionSweep & inspection
Caps & crownsCaps & crowns
Flue reliningFlue relining
Masonry repairMasonry repair
Gas fireplace serviceGas fireplace service
Every visit starts with

Level 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed

Worth knowing

Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.

Get your free estimate

Fast, Reliable Dryer Vent Cleaning Across Leander

Dryer vent cleaning in Leander typically costs $95 – $185 and is usually completed the same visit. We work throughout 78641, 78645, and 78646, from Crystal Falls and Travisso to the quieter lake-side pockets near Volente. If your dryer is taking 60-plus minutes per load or the laundry room smells like burnt lint, the vent is telling you something. Call (877) 644-8036 and we’ll get it cleared.

Call (877) 644-8036

We’re based in Georgetown, which puts us about 20 minutes from most Leander neighborhoods. That proximity matters when a vent is so packed with lint that every cycle is a fire risk. Brent Calloway built Resolute Chimney Sweep around a simple idea: dryer vents and chimneys share the same stakes. Both handle hot air and combustion exhaust. Both fail quietly until they don’t. Our Dryer Vent Cleaning service exists because most chimney companies won’t touch dryer vents, and most appliance repair outfits don’t understand venting physics. We do both.

Leander’s housing stock makes this work different from what we see in Georgetown or Liberty Hill. The 2000s – 2020s subdivisions that boomed along the 183/183A corridor were built fast, and dryer vents were an afterthought. Builder-grade plastic flex duct, long runs, tight chases. That’s the environment we work in every week.

Dryer Vent Cleaning in Leander: What It Costs and What You Get

A standard dryer vent cleaning in Leander runs $95 – $135 for a single-story home with a wall termination. Two-story homes or vents that run to the roof run $135 – $185. If the vent shares a chase with a prefab fireplace flue, which is common in Crystal Falls and Bryson, expect the higher end. We give the exact price before we start, and the estimate is free. No surprise line items.

  • Single-story, wall termination: $95 – $135
  • Two-story or roof termination: $135 – $185
  • Shared chase with fireplace flue (requires extra inspection time): $150 – $185
  • Crushed or kinked duct replacement (rigid metal, per linear foot): $18 – $30
  • Termination cap replacement (professional-grade, pest-blocking): $35 – $65

What affects the price in Leander specifically? Roof terminations, for one. A lot of the homes off Ronald Reagan Boulevard and around Travisso have roof vents, which require ladder work and take longer. Shared chases with the fireplace flue add inspection time because we check both systems while we’re there. And if the original builder installed plastic flex duct that’s now crushed, we’ll recommend replacing it with rigid metal. That’s a material cost you can see on the invoice, and we’ll show you the damaged section before we swap it.

Call (877) 644-8036 for an exact quote. Estimates are free, and we’ll tell you plainly if the vent can wait or needs to be done now.

Explore

Styles & brands we work with

Sweep & inspection
Sweep & inspection
Caps & crowns
Caps & crowns
Flue relining
Flue relining
Masonry repair
Masonry repair
Gas fireplace service
Gas fireplace service

Why Resolute Chimney Sweep Is the Team Leander Homeowners Call for Dryer Vents

Most chimney companies in central Texas don’t clean dryer vents. Most handymen don’t understand building codes, chase construction, or the physics of lint accumulation in long horizontal runs. We’re not either of those. We’re a chimney and exhaust specialist that handles the full scope of dryer vent work, from a basic clean-out to replacing a crushed run of flex duct with rigid aluminum pipe.

Brent Calloway’s approach to this company was straightforward: use professional-grade materials, do the job to code, and never recommend work the customer can’t verify. That’s why we stock DuraFlex rigid and semi-rigid aluminum vent systems, not whatever rolls are cheapest at the hardware store. When a vent in a Leander home needs replacement, DuraFlex gives the homeowner a product that resists crushing, meets UL 2158A standards, and will outlast the original builder-grade plastic.

We also do something most vent cleaners don’t: we use a camera inspection. Before and after. You see the blockage, we clear it, and then we show you the clean run. If the vent shares a chase with a prefab fireplace flue, we inspect both. That matters in Leander because the shared-chase construction is so common in the 2000s – 2020s homes along 183A.

And the name Resolute means we see it through. If we find a firebox issue during a dryer vent visit, we’re a chimney repair company too. We don’t hand you a phone number for someone else. One call covers the sweep, the vent, and the repair.

Our Dryer Vent Cleaning Services in Leander

Dryer Vent Cleaning

This is the core service. We connect a rotating brush system to the vent run and pull every bit of lint, debris, and nesting material out through the termination. For Leander homes, especially two-story builds off Bagdad Road or in the Mason Hills area, we typically find two to three pounds of lint even when the dryer seems to be “working fine.” A full clean-out usually takes 45 to 75 minutes depending on run length and access.

Dryer Vent Cleaning

Dryer Vent Inspection

Inspection is camera-based and included with every cleaning. We run a scope through the full duct run and look for kinks, separations, gaps, and pest damage. In Leander’s newer subdivisions, the most common finding is a crush point where the builder zip-tied the flex duct too tight inside the wall chase. That pinch point is a lint trap. The camera confirms it, and we show you the image.

Dryer Vent Inspection

Dryer Vent Termination Cap Clearing

The termination cap is where the vent exits the house. In Leander, wasps and birds love these. The original builder cap is usually a basic flap style with no pest screen, and during the long off-season from May to October, wasps build nests inside the opening. We clear the cap, vacuum the dead nest out, and replace the termination with a pest-blocking model from Copperfield or Olympia Chimney when needed. In Crystal Falls, we pulled a termination sealed completely shut by a wasp nest behind the original builder cap. The dryer had been venting into the wall for weeks.

Dryer Vent Termination Cap Clearing

Dryer Vent Duct Replacement

When the original flex duct is beyond saving, we replace it. In Leander, that usually means swapping plastic builder-grade flex for rigid aluminum or DuraFlex semi-rigid metal. We cut out the crushed section and run the new duct with proper support, no sharp bends. For homes where the vent shares a chase with the fireplace flue, we coordinate the replacement so both systems remain separated and code-compliant.

Dryer Vent Duct Replacement
Need help today?Fast, friendly service and a no-obligation free estimate.

Call (877) 644-8036

What happens when you call

  1. 1
    A real person answersNo phone trees — you reach a local pro.
  2. 2
    You get an upfront price rangeHonest numbers before anyone is dispatched.
  3. 3
    A background-checked tech heads outLicensed & insured, dispatched right away.
  4. 4
    You approve before work beginsNothing starts until you say go.

Trusted Brands We Service in Leander

We don’t install parts from retail shelves. Our vent replacements use DuraFlex and Copperfield products, the same components specified in professional chimney and venting supply catalogs. When a termination cap needs replacing, we use pest-blocking models built for central Texas weather, not the cheap plastic caps that crack in the first hard freeze. We keep common sizes on the truck, which means most Leander replacements happen the same day, not after a week wait for a special order.

Common Dryer Vent Problems We See in Leander Homes

Leander’s housing stock is specific, and the problems repeat. Here’s what we find most often:

  • Crushed plastic flex duct in the wall chase. Builders in the 2000s – 2020s ran cheap plastic duct and then closed up the wall. In many Leander homes, that duct was kinked or flattened during construction. The dryer still works, but lint builds at the pinch point until airflow drops. We see this in Crystal Falls, Bryson, and Travisso regularly.
  • Wasp and bird nests in the termination cap. The long hot season means caps sit unbothered for months. Wasps move in. By the time winter arrives and the dryer is running heavy loads, the vent is partially or fully blocked. We clear the nest, vacuum the run, and replace the cap with a screened model.
  • Shared chase with the prefab fireplace flue. Many Leander homes run the dryer vent and the fireplace flue through the same frame chase. If the vent duct has separated at a joint, lint blows into the firebox side. That’s a fire hazard we address while we’re already inside the access panel.
  • Sticky lint film from cedar pollen and humidity. Central Texas humidity plus cedar season creates a paste that coats the inside of the duct. This film grabs lint more aggressively than dry dust. It’s a big reason Leander vents clog faster than vents in, say, Lubbock or Amarillo.
Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade

Pricing for Dryer Vent Cleaning in Leander, TX

To state it plainly: a typical dryer vent cleaning in Leander costs $95 – $185. The spread depends on the house. A single-story ranch home around 78645 with a short wall vent is at the bottom. A two-story Travisso home with a roof termination and a shared fireplace chase is at the top. Replacement duct work adds $18 – $30 per linear foot for rigid metal, and a new pest-blocking termination cap runs $35 – $65.

We quote the full price before starting. You know the number, we know the number, and the estimate is free. If we find something beyond the vent, like a firebox issue in the shared chase, we’ll show you camera footage and give you a separate quote for the repair. Nothing is recommended without proof you can see.

Call (877) 644-8036 for a free estimate. We’ll ask about your home’s age, where the dryer sits, and whether the vent runs to the wall or roof, then give you a firm price range before we arrive.

The Shared Chase Problem: A Leander-Specific Vent Hazard

Here’s something most dryer vent pages won’t tell you, and it’s the reason we know Leander homes so well. In the 2000s – 2020s subdivisions built along the 183/183A corridor, builders often ran the dryer vent duct and the prefab fireplace flue through the same framed chase. It saves space and keeps the exterior clean. But if the dryer vent separates at a joint inside that chase, hot lint-laden air blows into the firebox side of the flue. Lint is essentially kindling. Pile it against a warm gas-log firebox and you’ve created a condition that should never exist.

This is why the annual NFPA 211 chimney inspection still applies in Leander, even when the dryer vent is clean. The two systems influence each other when they share a chase, and a camera inspection of one without checking the other misses half the picture.

We ran a call in Crystal Falls where the homeowner called about a musty smell in the laundry room. The dryer vent had been sealed shut by a wasp nest behind the original builder cap, and the 4-inch flex duct was kinked behind the firebox chase. Lint had backed up and was blowing into the side of the firebox every time the dryer ran. We replaced the crushed section with rigid DuraFlex, cleared the entire run, and the homeowner noticed the dryer finishing faster within a week. The laundry room smell was gone. That’s the job.

We Also Serve Cities Near Leander

Our trucks cover Leander and the surrounding communities. We’re regularly in Cedar Park, Hudson Bend, Jonestown, and Lago Vista for dryer vent cleaning and chimney work. Same pricing, same camera inspection, same professional-grade materials. If you’re in any of these areas, call (877) 644-8036 and we’ll get you on the schedule.

Serving Leander, TX — Our Local Coverage Area

We’re based in the Leander area and know this community well. Use the map below to see our service coverage — if you’re nearby, we can almost certainly help.

FAQs – Dryer Vent Cleaning in Leander

Get Your Leander Dryer Vent Cleaned Today

If your dryer runs hot, takes forever, or leaves the laundry room smelling like burnt dust, the vent needs attention. We’ll camera-inspect the run, clean every foot of it, and show you the proof when it’s done. We serve all of Leander, from Crystal Falls to Lake Travis, and we quote the price before we start. Call (877) 644-8036 for a free estimate.

Written by Brent Calloway, Owner at Resolute Chimney Sweep, serving Leander and central Texas with dryer vent cleaning and chimney services.

Why Leander Chooses Resolute Chimney Sweep

We set the standard for dryer vent cleaning in Leander.

Evidence Before Recommendations

Every sweep includes a camera inspection and a photo report. If we find something, you see it before we quote it — no repair is ever recommended on our word alone.

Licensed & Insured

Fully certified technicians who meet all local and state licensing requirements.

Upfront Pricing

No hidden fees, no surprises. You approve the price before any work begins.

Guaranteed Work

Every repair and installation is backed by our workmanship warranty and satisfaction guarantee.

How It Works in Leander

Getting your dryer vent cleaning handled is simple and fast.

1

Call or Request a Free Estimate

Tell us about your dryer vent cleaning needs and we provide an upfront, transparent quote — no obligation, no hidden fees.

2

Licensed Technician Dispatched

A background-checked, certified technician arrives in Leander — typically within 30–60 minutes, with parts stocked on the truck.

3

Problem Solved, Guaranteed

We complete the job to your full satisfaction, backed by our warranty and 100% satisfaction guarantee.

What happens when you call

  1. 1
    A real person answersNo phone trees — talk to a local dryer vent cleaning pro.
  2. 2
    You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
  3. 3
    We come out and measureLicensed & insured, at a time that suits you — the visit and the quote are both free.
  4. 4
    You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.

What Leander Customers Say

Trusted by homeowners across Leander and surrounding areas.

★★★★★

"Fireplace had never drawn properly since we moved in. He found the damper was only opening halfway due to a bent linkage and fixed it in ten minutes."

Beatriz Guzman · Verified customer
★★★★★

"Cap keeps the birds out now, which after two springs of scratching noises is worth every penny."

Henry Kim · Verified customer
★★★★★

"Creosote buildup was worse than I realized. He measured it, showed me the glazing on the flue with the camera, and was honest that we were closer to a chimney fire than I wanted to hear."

Gabriela Castillo · Verified customer

Ready for Dryer Vent Cleaning in Leander?

Call now for a free estimate — or request one below. Licensed, insured, and here with fast after-hours help in Leander.

(877) 644-8036

Request a Free Estimate in Leander

Tell us about your dryer vent cleaning needs — we'll respond within the hour.

By submitting this form, you confirm you have read our Privacy Policy and agree to be contacted through phone, text, or email regarding your project, including by the service partners who may complete the work.

Prefer to text? Text Now
Areas We Serve
Call Now - 24/7 Dispatch